Skip to content
Petro

What should be checked when one shift hands over to the next?

For station managers, owners · By the Petro team · Last reviewed

The short answer

At every handover, read and agree each pump's meter with both shifts present, settle every outgoing pumper's cash, slips and credit bills, dip the tanks, and count the float and any cash still on site. Anything that is not agreed at the handover becomes an argument later, because the next shift's figures start from what the last shift left. Keep a short written checklist and have both the outgoing and incoming person sign it.

Why does the handover matter so much?

Every figure on a shift depends on where the previous shift ended. The closing meter reading of one shift is the opening reading of the next, the closing dip is the next opening stock, and the cash in the drawer belongs to someone. If the handover is rushed, a mistake on one shift lands on the next, and an honest pumper ends up explaining a shortage they did not cause.

A good handover takes a few minutes per pump. It is quicker than sorting out a disputed shortage a week later.

What goes on the handover checklist?

  1. Meter readings. Read every nozzle's meter with the outgoing and incoming pumper both looking at it, write it down, and both sign. Electronic and mechanical totals should both be noted where the pump has both.
  2. Tested litres. Record any litres tested during the shift and confirm they were poured back.
  3. Credit bills. Collect every credit bill written on the shift and check each one has the customer, vehicle, litres, pump and a signature.
  4. Card and digital payments. Run the card machine's shift or batch total if it has one, collect the slips, and list any QR or wallet payments with their references.
  5. Cash. Count each outgoing pumper's cash with them, add their cash drops, and settle it against what they owe for the shift.
  6. Dips. Dip every tank, or at least those whose pumps were busy, after the pumps have been idle for a few minutes.
  7. Deliveries. Note any fuel delivery received during the shift, with its delivery note and the dips before and after.
  8. Float and petty cash. Count the change float and the petty cash box and record what was spent, with receipts.
  9. Faults and events. Write down any pump fault, a nozzle taken out of use, a price change, a customer complaint or anything unusual.

What if the readings do not agree?

Stop and sort it out before the incoming pumper starts selling. Read the meter again together. If the closing reading written by the outgoing shift is different from what the meter shows now, and no fuel has been sold in between, the written figure is wrong and should be corrected with both people signing the change.

If fuel was sold between the reading and the handover, for example because a customer arrived while the readings were being taken, record that sale against one shift or the other and say which. Never let the new shift start from a reading nobody has agreed.

Who should be present at the handover?

At least the outgoing and incoming pumper for each pump, and the manager or supervisor responsible for the shift. Where the station has one cashier for several pumpers, the cashier should be there for the cash count. Readings, dips and cash counts done by one person alone are the ones most often disputed later.

How do I keep handovers consistent?

  • Use the same printed or digital checklist on every shift, in the same order.
  • Hand over at a fixed time, and close the shift's records before the next shift starts selling.
  • Keep the signed checklists, so a question raised days later can be answered from the paper.
  • Train relief staff on the checklist too: handovers go wrong most often on days when the usual people are away.
  • Review the past week's checklists once a week and follow up on anything left open.

Frequently asked questions

Should the outgoing pumper leave before the cash is counted?
No. Count the cash with the pumper there. A count done after they leave cannot be checked by them, and any difference becomes a dispute about trust instead of about figures.
Do I need to dip the tanks at every shift change?
Dipping at every handover gives you a stock figure for each shift and makes losses easier to trace. If that is not practical, dip at least once a day at the same time, and always before and after a delivery.
What if a pump is out of order at the handover?
Record the meter reading anyway and note that the pump is out of use. When it is repaired, read it again before it goes back into service, so any change in the reading during the repair is explained.

How Petro handles this

Petro keeps one open shift per station, and the previous shift must be submitted before the next one opens, with each pump's closing reading becoming the next shift's in reading. Before a shift can be submitted, Petro checks that every pump is closed, every cash drop is allocated, no internal oil usage is left in draft, and, where the station uses them, that dips are in and the shift agrees with the pumpers' worksheets, and it says exactly what is missing.

See fuel operations in Petro

This guide is general information for Sri Lankan fuel stations, written by the Petro team. Figures in examples are made up. For a decision about your own tax or legal position, check with your accountant or the authority named in the sources.

See Petro running on your own numbers.

Tell us how many pumps you run and how you close the day today. We come back with a walkthrough built around your station, not a generic demo tenant.

30 days free · No card needed · A guided demo · Keep everything you enter · Cancel anytime, no charge

No obligation. We reply within one working day.