How do I check for water in a fuel tank?
For owners, station managers · By the Petro team · Last reviewed
The short answer
Spread a thin layer of water-finding paste on the bottom of the dip stick, lower it until it touches the tank floor, hold it for the time the paste instructions give, and lift it out: the paste changes colour where it touched water, so the height of the colour change is the depth of water. Do it at the same time as a routine dip, after the tank has rested, and always after heavy rain and before and after deliveries. Any water should be recorded, its source found, and removed before it reaches customers' vehicles.
Why does water in the tank matter?
Water is heavier than petrol and diesel, so it sinks to the bottom of the tank. A small amount sitting below the pump suction may do no harm at first, but it grows, and when it reaches the suction it is pumped into customers' vehicles. In diesel, water also encourages microbial growth that forms sludge and blocks filters.
Water also distorts your stock. A plain dip reads the total depth of liquid, so water at the bottom is counted as fuel. If water is coming in, the tank can look fine on paper while you are actually selling less fuel than you think.
How do I check with water-finding paste?
- Let the tank rest for a while with the pumps on it idle, so any water has settled to the bottom. Early morning before sales is a good time.
- Clean and dry the bottom part of the dip stick.
- Spread a thin, even layer of water-finding paste on the bottom few centimetres of the stick, on the side you will read.
- Lower the stick slowly and vertically until it rests on the tank floor at the dip point. Do not bang it down.
- Hold it still for the time given on the paste, then lift it straight out.
- Read the height where the paste has changed colour. That is the depth of water at the dip point. Convert it to litres from the bottom of the calibration chart if you want an estimate of the volume.
- Record the reading with the date and time, wipe the stick clean, and close the dip cap.
Where does the water come from?
- Rainwater getting in through a loose, damaged or missing fill cap or dip cap, or through a fill point in a chamber that floods.
- Groundwater entering through a damaged tank or line, which is more likely where the water table is high and during the monsoon.
- Condensation inside a tank that is often kept low, as warm moist air in the empty space cools. This usually adds water slowly.
- The delivery itself, if the bowser carried water. Checking the tank before and after a delivery tells you whether a load brought water with it.
What should I do if I find water?
- Check the other tanks too, and check again after a short while to confirm the reading.
- Look at the obvious entry points first: fill and dip caps, their seals, and whether the chamber around the fill point holds rainwater.
- If the water appeared right after a delivery, report it to the supplier with your before and after checks.
- If the water level keeps rising with no delivery and no rain, treat it as a possible leak and have the tank tested.
- Have the water removed by your oil company or a qualified contractor before it gets near the pump suction. Do not try to pump it out through the dispensers.
- Adjust your stock records for the water removed, so the book stock reflects only fuel.
How often should I check?
- At least once a week on every tank, as part of a routine dip.
- After every spell of heavy rain or flooding around the forecourt.
- Before and after each delivery, so that water in a load can be told apart from water already in the tank.
- More often on any tank where you have found water before, or where losses are unexplained.
Frequently asked questions
- Can I see water by looking at a fuel sample?
- Sometimes: a sample drawn from the very bottom of the tank may show water as a separate layer or a cloudy look. But the paste on the dip stick is quicker, measures the depth, and is the normal station check.
- Does water-finding paste work for both petrol and diesel?
- Water-finding paste reacts to water, not fuel, so it works in both. Use paste meant for water finding, not fuel-finding paste, which reacts to fuel instead.
- Is a little water normal?
- Any water is worth recording, but a trace that does not grow is less worrying than a level that rises. The trend over several checks tells you whether you have a source to fix.
How Petro handles this
Petro keeps each tank's dip reading against the book stock, with the difference on every reading and a chart over time, so a tank that starts gaining or losing stands out the day it happens. When water is removed or a dip is accepted as the true fuel stock, a Stock Reconciliation sets the books to the counted quantity and posts the difference at cost.
See stock in PetroThis guide is general information for Sri Lankan fuel stations, written by the Petro team. Figures in examples are made up. For a decision about your own tax or legal position, check with your accountant or the authority named in the sources.
